phone
Hotline and help
+48 87 737 1900
Mon - Fri 8:00 - 18:00, Sat 9:00 - 14:00
Save to shopping list
Create a new shopping list
Are you sure you want to remove products from the basket?
Safe shopping
Idosell security badge

How many mm of tread does a new tire have?

2026-11-18

A new tire doesn't always have 8mm of tread. Depending on the model and intended use, the factory groove depth can range from around 6 to 10mm, and in some designs, even beyond that.

Why do new summer, winter, and all-season tires differ in tread depth? Does 7 mm on a new tire indicate inferior quality? We examine typical values, Polish regulations, and safety recommendations. We also show you how to measure tire wear yourself.

How much tread does a new tire have? Comparison in millimeters

There is no single tread depth that applies to all new car tires. Much depends on the tire's construction, type, and even the specific size variant.

Tread depth – the most important values

Swipe the table sideways to see all columns →

Tire type New tire - approximate Recommended replacement threshold
Summer approx. 6–8 mm approx. 3 mm
Winter approx. 7–10 mm approx. 4 mm
Year-round approx. 7–9 mm about 4 mm before winter

The ranges for new tires are approximate, not factory standards. The 3 and 4 mm thresholds are safety recommendations, not Polish legal requirements. Sources: Continental, ADAC.

A summer tire with 7 mm of factory tread doesn't have to be used or defective. A fair assessment requires comparing this parameter with the data for a specific model, not with a single industry-wide standard.

What determines the factory tread depth?

The tread is the part of the tire that contacts the road. It is made up of blocks, ribs, grooves, and fine cuts known as sipes. Depth is measured from the tread surface to the bottom of the main grooves.

Why do manufacturers use different depths?

Designers must balance several requirements. Deeper grooves provide more space for water and slush, but taller knobs can deform more under load. Stiffer knobs, on the other hand, can improve handling precision on dry asphalt. Rolling resistance, noise, and wear rates are also important considerations.

Therefore, performance is determined not only by the number of millimeters. The rubber compound, the channel layout, the number of sipes, and the overall construction of the tire are equally important.

Can the same model in two sizes have a different tread?

Yes. Individual size versions of a single model may differ in design and tread pattern. However, there is no rule that a 19-inch tire always has deeper grooves than a 15-inch tire. Such a comparison must be made for specific products.

How many mm of tread does a new summer tire have?

New summer tires typically have around 6–8 mm of tread , although the exact amount depends on the model. Their tread pattern is designed to perform on both dry and wet asphalt during the warmer months.

Adequately stiff blocks help transfer forces during braking and cornering. Longitudinal and lateral grooves, meanwhile, are responsible for displacing water from under the tire. This doesn't mean that a model with 8 mm of tread will automatically perform better in rain than another model with 7 mm. The entire structure matters.

How many mm of tread does a new winter tire have?

New winter tires typically have a tread depth of around 7–10 mm. Continental suggests a typical range of 7–9 mm, while other designs also typically have tread depths around 10 mm.

In winter tires, sipes are crucial, creating additional gripping edges. Deeper grooves also facilitate handling in snow and slush. On ice, tread depth alone isn't enough to assess traction: the rubber compound and sipe geometry are equally important.

How much tread does a new all-season tire have?

New all-season tires often have around 7–9 mm of tread . This value is approximate and does not constitute a mandatory standard.

All-season tires combine solutions used in summer and winter tires. They must provide predictable performance on dry asphalt, in rain, and in snow. Individual models differ in the layout of grooves, sipes, and block stiffness, so their properties are best verified through independent testing.

If the tire is to be used in winter, it is worth checking for the 3PMSF marking (mountain with snowflake symbol), confirming that it meets the requirements for grip in snow.

What about sports and off-road tires?

Semi-slick road and track tires may have shallower grooves because they're designed with a focus on dry performance. AT and MT off-road tires, on the other hand, utilize large tread blocks with wide spaces between them. Therefore, tires for these different applications shouldn't be judged solely by tread depth.

How does tread wear affect safety?

As the tread wears, the space available for water and slush drainage decreases. This is especially important in rain, when the tire can lose direct contact with the road – a phenomenon known as aquaplaning.

What did the ADAC study from 2026 show?

In September 2026, ADAC published a test of five winter tire models, compared in new condition and after tread reduction to 4 mm and 2 mm. The results confirmed that deeper wear significantly reduces safety reserves, especially on wet asphalt.

Worn tread and braking in the rain Average results of five winter tire models • ADAC, 08/09/2026

Braking distance on wet roads increased by approximately 5.3 meters under the tested conditions. Below are the additional results for a 2 mm tread depth compared to new tires:

−22% average change in longitudinal aquaplaning test result
−52% average reduction in safety margin for lateral aquaplaning

The graphic shows the results of a specific test, not a prediction for every tire. The bar lengths are proportional to the reported braking distances. Source: ADAC, 2026 .

However, the performance degradation isn't the same for every tire and road surface. When driving on snow, both groove depth and sipe performance are important. On ice, temperature and rubber compound are also important. Therefore, tread depth alone doesn't replace an assessment of the overall tire condition.

Minimum tread depth in Poland – regulations and recommendations

In Poland, the basic benchmark for standard passenger car tires is 1.6 mm . Pursuant to § 11, paragraph 7, point 4 of the Regulation on the technical conditions of vehicles, tires whose indicators indicate the wear limit are prohibited. For tires without such indicators, the regulation stipulates a tread depth of less than 1.6 mm.

Three values ​​worth remembering
1.6 mm Legal Limit Typical limit indicated by the TWI in a passenger tire
3 mm Summer Tires Recommended Replacement Threshold According to ADAC
4 mm Winter and all-season Recommended threshold, especially before winter driving

1.6 mm is the limit resulting from regulations and wear rates. Values ​​of 3 and 4 mm are safety recommendations – in Poland, they are not separate statutory limits.

Driving on tires that don't meet technical requirements can result in a fine, confiscation of the vehicle registration certificate, and a negative technical inspection. Tire condition can also be important when analyzing the causes of a road accident and insurance liability, but it doesn't automatically result in a denial of comprehensive insurance compensation in every case.

Important before traveling abroad

Some countries have additional requirements for winter tires, such as higher minimum tread depths. Before traveling, check the regulations in your destination and transit countries.

When should you actually replace your tires?

ADAC recommends considering replacing summer tires at around 3 mm, and winter and all-season tires at around 4 mm. This is especially important for drivers who regularly drive fast in the rain or drive in snow and slush in winter.

These thresholds don't mean that winter tires suddenly stop working at 3.9 mm. Performance deteriorates gradually, and the condition of the specific model and road conditions also play a role.

How to measure tread depth yourself?

Visual inspection is not very accurate. It's best to use an inexpensive tread depth gauge or a depth gauge. Measurements should be taken in several places.

Measuring tread in 6 steps

  1. Secure your car.

    Park on level ground and make sure the car cannot move.

  2. Clean the selected groove.

    Remove any stones or dirt that may prevent the meter from resting properly.

  3. Place the probe in the main groove.

    Rest the gauge base on the tread and the probe on the bottom of the channel, avoiding the TWI lugs.

  4. Read the result in millimeters.

    Record the result and then repeat the operation in several adjacent grooves.

  5. Check several places around the circumference.

    Measure the tread at various points and on the inside and outside of the rolling part.

  6. Compare results.

    If one zone is noticeably more worn, also check the pressure, geometry and condition of the suspension.

TWI indicator – where to find it?

TWI (Tread Wear Indicators) are small rubber ridges at the bottom of the main grooves. The ridges' positions are marked on the tire sidewall by the letters "TWI," triangles, or manufacturer symbols. In standard passenger tires, they indicate a limit of approximately 1.6 mm.

When the tread surface reaches the wear limit, the tire needs to be replaced. Some winter tires also have additional wear indicators of around 4 mm – this should not be confused with the legal TWI limit.

Can you check the tread with a 5 PLN coin?

Yes, but only as a guide. The silver ring of a five-zloty coin is approximately 4 mm wide. If you insert the coin perpendicularly into the main groove, the visible ring may indicate that the tread is less than approximately 4 mm.

A coin is not a substitute for a meter

The 5-zloty test helps quickly check the 4mm tread area, but it doesn't precisely determine whether a tire has 1.6mm, 2mm, or 3mm of tread. If in doubt, use a tire gauge or ask a service center for a measurement.

Is tread depth alone enough to assess a tire?

No. A tire with deep tread may need to be replaced for other reasons. During your inspection, look for bulges, cracks, cuts, uneven wear, and the age of the tire.

Rubber gradually ages, even in cars with low mileage. Michelin recommends preventative tire replacement after 10 years from the production date, even if the tread appears good. This is not a statutory deadline in Poland, but rather a manufacturer recommendation.

Summary – how much tread should a new tire have?

New car tires typically have around 6–10 mm of tread depth, but the exact value depends on the model and intended use. Summer tires typically have shallower grooves than winter tires, but this isn't a universal rule.

What's most important isn't just how many millimeters of tread a tire has on purchase, but also how it performs during use. Monitor wear at several points, don't delay replacing damaged tires, and remember that the legal limit of 1.6 mm doesn't guarantee full performance on wet or snow-covered roads.

Frequently Asked Questions (FAQ)

How many mm of tread does a new summer tire have?

Typically around 6–8 mm, although variations can occur depending on model and size. A lower factory reading doesn't automatically mean the tire has been used.

How much tread does a new winter tire have?

Most often around 7-10mm. Continental indicates a typical range of 7-9mm, but some designs have deeper grooves.

How many mm of tread does a new all-season tire have?

For many models, this is around 7–9 mm. The value for a specific tire depends on its design and size.

What is the minimum tread depth in Poland?

The basic reference point is 1.6 mm. The regulations also refer to factory wear limits (TWI).

Do winter tires need to be replaced at 4 mm?

This is not an obligation under Polish law. However, ADAC recommends changing winter tires at around 4 mm for safety reasons.

Is a new tire with 7mm tread worse than a tire with 9mm?

Not necessarily. Depth alone doesn't determine grip or quality. The compound, construction, and test results of a given model must be considered.

What is the best way to measure tread depth?

Using a dedicated tread depth gauge or a depth gauge caliper, repeat the measurement in several places across the width and circumference of the tire.

Return to the beginning of the article ↑
Show more entries from November 2026
pixel